This program installs or re-installs SureTrak Version 2.0.  If
you're currently running SureTrak Version 1.0, this program will
upgrade it to Version 2.0.

You can stop the installation at any time by pressing the Esc key
if there is no "Accept  Edit  Quit" command line visible, or by
choosing Quit if the command line is visible.  Press Esc to clear 
any help message, including this one.

As you proceed through the installation, you may be asked whether 
this program should overwrite certain SureTrak files if they 
already exist.  This installation program does not affect any 
nonSureTrak files on your computer, with one exception.  If your 
CONFIG.SYS file currently allows fewer than 30 files open, you'll 
get to specify whether you want this installation program to edit 
it to allow 30 files or whether you prefer to do it yourself.  
This program does not change your AUTOEXEC.BAT file.

As part of the installation of your upgrade 
from SureTrak Version 1.0 to SureTrak 2.0, 
your SureTrak 1.0 files must be converted.  
Use this screen to direct this installation 
program to the location of the Version 1.0 
files so that they may be converted.  Press
~3E~ to edit the screen; press ~3A~ to accept it 
when it shows the location of 1.0 files.

If you don't know where your SureTrak 1.0 
files are, you may return to the command line 
and press F3 to execute a DOS command like 
DIR.  Or you may press ~3Q~ to stop this 
installation and return to DOS.  By default, 
SureTrak 1.0 was installed in the \SURETRAK 
directory on the C drive.

Press Esc to clear this help message.

Enter the drive and directory where your 
SureTrak Version 1.0 files are located, 
separated by a colon as in this example:

           C:\SURETRAK

If you don't know where your Version 1.0 files 
are, press Esc to use the previous help screen 
to navigate through your directories and find 
the files, or press Esc three times to return 
to the command line and then press F3 to 
execute a DOS command to look for the files.

Enter a DOS command and press 
Enter. The command will be executed 
and you will return immediately to 
SureTrak Installation.

The serial number is the registration 
number assigned by Primavera Systems, 
Inc. to this copy of SureTrak.  The 
serial number verifies your identity as 
a customer when you call for support; 
it appears on the first screen you see 
each time you start using SureTrak.

Press ~3E~ to edit this screen; enter your 
name or your company's name to further 
identify this copy of SureTrak as yours.  
Then press ~3A~ to accept this screen.

Press Esc to clear this help message.

Enter your name or your company's
name to identify the registered 
owner of this copy of SureTrak.

Use this screen to control the installation 
of SureTrak Version 2.0.  Specify the disk
from which you boot DOS; the drive and 
directory from which you are installing 
SureTrak 2.0 (usually your floppy drive); 
the drive and directory where SureTrak 
Version 2.0 should be located; and the type 
of monitor you'll use with SureTrak.

Press ~3E~ to edit the screen.  When you've 
filled out the blanks, press ~3A~ to accept it 
and proceed with the installation.

Specify the drive from which you
boot DOS.  Normally, this is C:

Specify the drive and directory from
which you are installing SureTrak
Version 2.0.  For example, if you are 
installing directly from the diskettes, 
and your drive is named A, enter:
              A:

Specify where you want SureTrak 2.0 
to be -- which drive and directory.
For example, if you want to install 
SureTrak to its own directory under 
the root directory on drive C, enter:
           C:\SURETRAK

Specify whether you have a color 
monitor or a monochrome monitor 
(black-and-white, -amber, or -green).

DOS cannot be booted from the drive you 
specified.  (This is normal if you're 
running on a network.)  If you continue 
without changing the boot drive, 
installation will proceed normally except 
that your CONFIG.SYS file will not be set 
to FILES=30; you will have to edit this 
file separately after installation is 
complete.  You may press ~3C~ to continue 
without changing the boot drive, or you 
may press ~3E~ to edit the screen again and 
change your entry for the DOS boot drive. 

The SureTrak program file, ST.EXE, already 
exists in the directory you specified you 
wanted to load Version 2.0 into.  Press ~3Y~ if 
you want to replace this ST.EXE with the one 
you are now installing; press ~3N~ to halt the 
installation without overwriting the file; 
press Esc twice to return to the appropriate 
screen without overwriting the file so that you 
may change your instructions on the screen.

Ensure that the installation disk 
is in the drive; press Enter to 
continue.

Your installation of SureTrak Version 
2.0 has been successfully completed.  
You may remove the last diskette from 
the drive.  The Getting Started section 
of the SureTrak Version 2.0 manual 
includes an introduction to using 
SureTrak Version 2.0 and configuring 
it for your printer and/or plotter.

Press Esc to clear this help message.

Your CONFIG.SYS file currently has FILES set to 
a number less than 30.  In order to run SureTrak 
Version 2.0, FILES must be set to at least 30.  
Press ~3Y~ if you want this installation program 
to edit CONFIG.SYS and change the line to 
FILES=30, leaving a backup of the original as 
CONFIG.SMP in the directory into which you're 
installing SureTrak; press ~3N~ if you prefer to 
do it yourself, in which case CONFIG.SMP will 
contain the suggested version of your CONFIG.SYS.  
SureTrak Version 2.0 may not run properly unless 
FILES is set to 30 or greater.

ST2.BAT is the file that executes 
SureTrak Version 2.0 after changing 
to the \SURETRAK directory.  This 
file already exists on your computer.
Press ~3Y~ if you want to overwrite it 
with the ST2.BAT file as part of this
installation; press ~3N~ if you do not 
want to overwrite this file.

Insert the Install disk into the 
drive.  More files from this disk 
are required for SureTrak Version 
2.0 installation.

More files are required to complete 
installation of SureTrak Version 2.0. 
Please insert Disk 1 into the drive.

More files are required to complete 
installation of SureTrak Version 2.0.  
Please insert Disk 2 into the drive.

More files are required to complete 
installation of SureTrak Version 2.0. 
Please insert Disk 3 into the drive. 

More files are required to complete 
installation of SureTrak Version 2.0. 
Please insert Disk 4 into the drive. 



